10/22/2023 0 Comments RECALIBRATE DIGIDESIGN DCOMMAND 8Maybe they're supposed to be quirky and different, but while their visual appeal is a matter of opinion, they fall short on a practical level. That said, let's deal with my biggest criticism up front! The fader caps are weird, looking and feeling a bit like squashed beer-bottle tops. So, initial impressions are mostly good, and here's a sneak preview: I'm going to say a lot of good things about the Command 8, and it's one of the best all-round controllers I've used. Despite the obvious similarities with the 002, the design of the housing is better, moving from the other surface's slightly toylike 'scooped' appearance to something more traditional. This impression is reinforced by the way that the power supply screws securely into place, a simple but reassuring touch. From the pictures on Digi's web site I thought it would be small, light and, dare I say it, plasticky, but in fact it's a hefty and impressive piece of kit. The first thing that struck me about the Command 8 was that it's much bigger than I'd expected. A significant departure for Digidesign, moreover, is that Command 8 is not just for Pro Tools: it also runs stand-alone as a MIDI controller for any other capable software. Command 8 provides hands-on control of both Pro Tools LE and TDM software, with the same high level of integration and sophistication that we've come to expect since Pro Control, Control 24 and HUI. However, while the Command 8 is indeed similar to the 002's controller, the comparison doesn't do justice to the new unit's scope. Digidesign's Command 8 aims to offer the best of both worlds.ĭigidesign already offer a rackmounting variant on their Digi 002 interface, which offers the Pro Tools LE audio interface component without the control surface, and at first glance, their Command 8 appears to be the reverse: the control-surface element of the Digi 002 without the audio interface. The D-Control uses Penny and Giles faders.With fader controllers, you often have a choice of buying something dedicated to one software package, or a generic unit that gives versatility at the cost of tight integration. D-Control - To access the D-Control fader tests, press Utility, choose Test, then Fader.D-Command - To access the D-Command fader tests, press Utility, choose Test, then Fader.ProControl - To access the ProControl fader tests, press Utility (located on the Main unit), choose Test, then Fader.Control|24 - To access the Control|24 fader tests, press Utility, choose Test, then Fader.003 - To access the 003 fader tests, push the Utility button, then Test, and Fader.002 - To access the 002 fader tests, first enter Standalone mode, then press Utility, choose Test, then "Fadr." The 002 uses Alps faders.Command|8 - To access the Command|8 fader tests, press Utility, choose Test, then "Fadr." The Command|8 uses Alps faders.The main thing to look for is whether or not the “touch” is registered - the actual reading is of less significance and may vary (due to a difference in capacitance between users, the environment, and hardware). Please be aware, however, that the grounding in the environment and the capacitance of the operator can affect these readings significantly. Touch test will display the capacitance, in Hertz, of the fader when idle and when touched. Touch test will show you the current capacitance of the fader itself, and is most useful for the purposes of this article. Control surfaces that do not have this option automatically calibrate themselves when powered on if you experience similar problems on these consoles, simply power-cycle the unit. If you have faders that don't seem to travel the entire throw, or seem like their range is limited, you should recalibrate the faders by running this test. Recal will reset the throw of all faders. There are a total of 1024 steps (0-1023) for a 10-bit resolution throw. In these tests, the display will report which step-bit the fader is currently on. Group test allows you to move all faders together by only touching one. Triangle, Sine, Step, and Cycle tests will move the faders in the selected pattern up and down the fader throw. Read below for information on how to run and interpret these tests (note that some tests vary between products): ![]() ![]() ![]() These tests may include: Triangle, Sine, Step, Cycle, Group, Recal, and Touch. Be sure to test your control surface in a minimal environment before connecting other gear.įor each console, there are multiple fader tests. It is possible for another device in the room to cause touch problems on a unit that had been working fine previously.Try blowing out the fader track with compressed air. Dust can limit the responsiveness of the faders.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |